-
Arduino Uno R3 - Original Made in Italy
Arduino R3 is an open source hardware and software program used for roboticists, and lighting led , motors etc . Contains Variety of I/O pins including analog, digital, PWM and more. It is inexpensive and easy for beginners to use. It also has reset button to reset the program on chip.
Specifications:
- ATmega328 microcontroller
- Input voltage - 7-12V
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- 32k Flash Memory
- 16Mhz Clock Speed
Package Includes:
- 1 x Arduino Uno R3 board with Cable.
-
Arduino Mega 2560
Arduino Mega2560 is fitted with the ATMEGA16U2 chip which is an open source program. The power source is selected automatically either from USB connection or external power supply. The ATmega2560 has 256 KB of flash memory for storing code . It contains automatic reset software inbuilt with stronger reset circuit.
-
Arduino Due Board
Arduino Due board based on a 32-bit ARM core microcontroller (AT91SAM3X8E ) that allows operations on 4 bytes wide data within a single CPU clock including 12 digital I/O pins and 12 analog pins. It is compatible with all Arduino shields that work at 3.3V. it has a DMA controller that can relieve the CPU from doing memory intensive task. It contains automatic reset software. We can operate its drivers from any operating software’s. It has automatic reset software with usb host facilities.
-
Arduino Uno Protype Shield
Arduino Prototype Shield V.5 has a nice standard 0.1″x0.1″ prototying grid with big pads that comes with stacking headers and plain header. It is Compatible with tiny breadboards and there is a reset button and a general use button included in it. You can ues it with UNO, NG, Diecimila and Duemilanove Arduinos. The power arduino prototype rails down the middle and sides.
-
Arduino Mega Protype shield
Arduino Mega Prototype Shield comes with all hardware included and can be directly pulg into Arduino MEGA. It this we can use ‘mini’ or medium bearboard . There are lost of GND and +5V rails with a reset button up top. .There are Extra 6mm button and DIP prototyping area makes it easy to add more chips.It is compatible with Arduino Mega pinout. It has PCB design.
-
Arduino Gps Sheild
The Arduino Gps shield is based on EB-365 GPS module that comes with Micro SD interface. It has got a UART interface and a active antenna design with high receive sensitivity. It has got a extremely fast time to first fix at low signal level. It is compatible with Arduino Uno boards. It is easy to setup.
-
PIR Motion Sensor Detector Module HC SR501
Features :
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time are adjustable.
- Blockade time: 2.5s (Default)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
Package Includes :
1 x PIR Motion Sensor Detector Module HC SR501
-
Voltage Sensor Module
A module which is used as potential divider to reduce any input voltage by a factor of 5.It is based on principle of resistive voltage divider design it can make the input voltage of red terminal reduce 5 times of original voltage.
-
BMP180 Pressure Sensor
It helps to measure environment temperature and pressure and barometric pressure.by which we can calculate altitude which can be used in various application like weather monitoring, navigation with I2C (“Wire”) interface. It measure the absolute pressure of the air around them how data are interpreted you can monitor change in weather, measure altitude. It has flexible supply voltage range with ultra low noise power consumption and low noise measurement.
-
Arduino UNO R3 Clone
Arduino UNO R3 clone is made in china instead of Italy.There are two analog-input pins : A6 and A7 that are not found on traditional UNO boards. You will need to install a driver for your computer to recognize the on-board CH340G USB to serial converter.R3 clone has a USB connector for easy connection to computers for programming including a power jack, an ICSP header and a reset button.
-
Arduino Mega 2560 Clone
"The Arduino Mega 2560 is a open-source physical computing microcontroller board based on the ATmega2560. It includes 54 digital input/output pins where 14 can be used as PWM outputs , 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header,. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP)The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
The Mega 2560 R3 has an automatic reset software and also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin.. The Mega 2560 R3 works with all existing shields but can adapt to new shields which use these additional pins. The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux).
"
-
Arduino Leonardo
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 that includes 20 digital input/output pins where 7 can be used as PWM outputs and 12 as analog inputs , a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. We can simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to operate . The Leonardo has built-in USB communication that eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard. The drivers are automatically installed plugging with an USB cable to the PC. The software can be found in the official site .