L298 Motor driver based module. Small module which can be used with any circuit very easily. Controls 2 DC motors/ 1 Stepper motor in both direction. PWM/NON PWM control using jumpers. Diodes provided for back EMF protection.

Motor Driver Module Features:

• Driver chip: L298 dual H-bridge driver chip.
• Operates up to 35V DC
• Drive part of the peak current Io: 2A / Bridge
• Logical part of the terminal power supply range Vss :4.5V-5.5V
• Logical part of the operating current range: 0 ~ 36mA
• Maximum power consumption: 20W

HG7881 (L9110) module can be used to drive a small robots. The module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor. It has 800 mA continuous current output. It can be connected directly to the CPU.It has low static work current and low saturation pressure drop with other features as well.

The monster motor driver shield is capable of driving a pair of high-current motors as in this motor the L298H-bridge is replaced with a pair of VNH2SP30 full bridge motors. It has the feature of under voltage and over voltage shutdown alos current sensing available analog pin. It is capable of driving a high current motors.

1. The L293D Motor Driver Shield is expansion board based on the L293D chip. It is designed to drive up to 4 bidirectional DC motors with 8-bit speed selection. It can also drive 2 stepper motor i.e. Uni-polar or bipolar, coil or double coil, interleaved or micro stepping. At range of 4.5V to 36V power supply, it provides up to 0.6A per bridge. It can be applicable in various electrical and DIY projects. 

The 7A Dual DC Motor Driver Module is an Ultra Small Dual Channel H-Bridge Motor Driver Module. It can drive 2 motors independently of up to 7A per Channel or under 160W. This motor driver features a UVLO which refers to Under Voltage Latch-Out.

L293d is a 4-channel driver that contains high voltage, high current. It is monolithically integrated. Simply this means using this electronic component user can use DC motors and power supplies of up to 12 Volts, which mostly look like a pretty big motor and the chip can supply a maximum current of 600mA per channel.

It is ideal for use in battery-powered smart cars, toy cars, robots. The supply voltage of this electronic component is 2V ~ 10V  and also it can drive two DC motors or 4-wire 2-phase stepper motors. It can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each can provide a continuous current of 1.5A, peak current up to 2.5A, thermal protection, and can be automatically restored.

This driver module is based on an unknown H-bridge, a high current, low voltage dual full-bridge driver. It can drive up to 2 DC motors up to 2Amp each, or drive one stepper motor or 2 solenoids up to 1.5 Amp each continuously and 2.5 Amp at peak.

The latest 3rd generation TB6565 Stepper Driver has been upgraded to the intelligent, professional and industrial-level drive set by re-designing the PCB board, embedding intelligent memory chip(professional version) and upgrading the external manual control tools (display panel and control pad).

This electronic device can control the output current within 160A.it has a  static standby current: only approx. 3MA.The signal type uses the sink-current control mode, supports direct control of most single-chip microcomputers, the signal isolation chip is isolated. The PWM signal frequency is supported within 200 kHz. The key ratio supports 0 to 98%. Use fast recovery diodes to prevent the induction of the electric motor power during engine startup. 

1. The ULN2003 Stepper Motor Driver Module is a Driver Module for stepper motor which is based on ULN2003 controller IC. It has A, B, C, and D four-phase LED that indicates the status of the stepper motor work. It can be suitable for using in high-power stepper motors for various DIY projects

Esp 12 motor shield is large current motor driven module can compatible with ESP12E Dev Kit and NodeMCU. It is  Dual high-power H-bridge drive with L293DD  chip. The module also has several pins and mostly used for DIY a WI - FI  RC smart car or any type of robotics and many more. It can drive two motors at oncewith a power swtich in-built.